data sheet the information in this document is subject to change without notice. before using this document, please confirm that this is the latest version. not all devices/types available in every country. please check with local nec compound semiconductor devices representative for availability and additional information. l-band pa driver amplifier gaas integrated circuit m m m m pg2128tb document no. pg10062ej01v0ds (1st edition) date published february 2002 cp(k) printed in japan ? ? ? ? nec compound semiconductor devices 2002 caution electro-static sensitive devices description the m pg2128tb is gaas mmic for pa driver amplifier which were developed for mobile phone and another l- band application. the device can operate with 3.0 v typ., having the high gain and low distortion. features ? operation frequency : f opt = 1 429 to 1 453 mhz (1 441 mhz typ.) ? supply voltage : v dd1 = 2.7 to 3.3 v (3.0 v typ.) : v dd2 = 2.7 to 4.2 v (3.5 v typ.) ? circuit current : i dd = 40 ma typ. @ v dd1 = 3.0 v, v dd2 = 3.5 v, v agc = 2.5 v, p out = +12 dbm ? high power gain : g p = 28 db typ. @ v dd1 = 3.0 v, v dd2 = 3.5 v, v agc = 2.5 v, p in = - 16 dbm ? gain control range : gcr = 40 db typ. @ v dd1 = 3.0 v, v dd2 = 3.5 v, v agc = 0.5 to 2.5 v, p in = - 16 dbm ? low distortion : p adj1 = - 60 dbc typ. @ v dd1 = 3.0 v, v dd2 = 3.5 v, v agc = 2.5 v, p out = +12 dbm, d f = 50 khz, 21 khz bandwidth. ? high-density surface mounting : 6-pin super minimold package (2.0 1.25 0.9 mm) application ? digital cellular: pdc 1.5 ghz etc. ordering information part number package marking supplying form m pg2128tb-e3 6-pin super minimold g2m embossed tape 8 mm wide pin 1, 2, 3 face the perforation side of the tape qty 3 kpcs/reel remark to order evaluation samples, contact your nearby sales office. part number for sample order: m pg2128tb
data sheet pg10062ej01v0ds 2 m m m m pg2128tb pin connections, marking and internal block diagram pin no. pin name 1v dd1 2gnd 3output/v dd2 4v agc 5gnd 6 input absolute maximum ratings (unless otherwise specified, t a = +25 c) parameter symbol ratings unit supply voltage1, 2 v dd1, 2 6.0 v agc control voltage v agc 6.0 v input power p in - 8dbm power dissipation p d 140 note mw operating ambient temperature t a - 30 to +90 c storage temperature t stg - 35 to +150 c note mounted on double copper-clad 50 50 1.6 mm epoxy glass pwb, t a = +85 c recommended operating renge (t a = +25 c) parameter symbol min. typ. max. unit supply voltage1 v dd1 2.7 3.0 3.3 v supply voltage2 v dd2 2.7 3.5 4.2 v agc control voltage v agc 0 - 2.5 v input power p in -- 16 - 10 dbm 1 2 3 6 5 4 g2m (top view) 6 5 4 1 2 3 (bottom view) (top view) 1 2 3 6 5 4
data sheet pg10062ej01v0ds 3 m m m m pg2128tb electrical characteristics (unless otherwise specified, t a = +25 c, v dd1 = 3.0 v, v dd2 = 3.5 v, p p p p /4dqpsk modulated signal input, external input and output matching) parameter symbol test conditions min. typ. max. unit operating frequency f opt 1 429 - 1 453 mhz circuit current i dd p out = +12 dbm, v agc = 2.5 v - 40 48 ma power gain g p p in = - 16 dbm, v agc = 2.5 v 26 28 - db adjacent channel power leakage 1 p adj1 p out = +12 dbm, v agc = 2.5 v d f = 50 khz, 21 khz bandwidth -- 60 - 55 dbc adjacent channel power leakage 2 p adj2 p out = +12 dbm, v agc = 2.5 v d f = 100 khz, 21 khz bandwidth -- 70 - 65 dbc gain control range gcr p in = - 16 dbm, v agc = 0.5 to 2.5 v 35 40 - db gain control current i agc v agc = 0.5 to 2.5 v - 250 500 m a
data sheet pg10062ej01v0ds 4 m m m m pg2128tb evaluation circuit (v dd1 = 3.0 v, v dd2 = 3.5 v, f = 1 441 mhz) 2.7 nh 1 000 pf 2 pf 3 pf 8.2 nh v dd1 v dd2 1 k w 6.8 nh 5 pf v agc out in 1 000 pf 1 000 pf 123 654 g2m the application circuits and their parameters are for reference only and are not intended for use in actual design-ins.
data sheet pg10062ej01v0ds 5 m m m m pg2128tb illustration of the test circuit assembled on evaluation board agc amp vagc l2 l1 l3 c6 c4 c5 r1 c1 c3 c2 vdd1 vdd2 in out using the nec evaluation board symbol values part number maker l1 2.7 nh tfl0816-2n7 susumu l2 6.8 nh tfl0816-6n8 susumu l3 8.2 nh tfl0816-8n2 susumu c1, c3, c6 1 000 pf grm39ch102j50 murata c2 2 pf grm39ck020c50 murata c4 3 pf grm39cj030c50 murata c5 5 pf grm39cj050c50 murata r1 1 k w rr0816 susumu
data sheet pg10062ej01v0ds 6 m m m m pg2128tb package dimensions 6-pin super minimold (unit: mm) 0.90.1 0.7 0 to 0.1 0.15 +0.1 C0.05 2.00.2 1.3 0.65 0.65 0.2 +0.1 C0.05 2.10.1 1.250.1 0.1 min.
data sheet pg10062ej01v0ds 7 m m m m pg2128tb recommended soldering conditions this product should be soldered and mounted under the following recommended conditions. for soldering methods and conditions other than those recommended below, contact your nearby sales office. soldering method soldering conditions condition symbol infrared reflow peak temperature (package surface temperature) : 260 c or below time at peak temperature : 10 seconds or less time at temperature of 220 c or higher : 60 seconds or less preheating time at 120 to 180 c : 120 30 seconds maximum number of reflow processes : 3 times maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below ir260 vps peak temperature (package surface temperature) : 215 c or below time at temperature of 200 c or higher : 25 to 40 seconds preheating time at 120 to 150 c : 30 to 60 seconds maximum number of reflow processes : 3 times maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below vp215 wave soldering peak temperature (molten solder temperature) : 260 c or below time at peak temperature : 10 seconds or less preheating temperature (package surface temperature) : 120 c or below maximum number of flow processes : 1 time maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below ws260 partial heating peak temperature (pin temperature) : 350 c or below soldering time (per side of device) : 3 seconds or less maximum chlorine content of rosin flux (% mass) : 0.2%(wt.) or below hs350 caution do not use different soldering methods together (except for partial heating).
data sheet pg10062ej01v0ds 8 m m m m pg2128tb m8e 00. 4 - 0110 the information in this document is current as of february, 2002. the information is subject to change without notice. for actual design-in, refer to the latest publications of nec's data sheets or data books, etc., for the most up-to-date specifications of nec semiconductor products. not all products and/or types are available in every country. please check with an nec sales representative for availability and additional information. no part of this document may be copied or reproduced in any form or by any means without prior written consent of nec. nec assumes no responsibility for any errors that may appear in this document. nec does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of nec semiconductor products listed in this document or any other liability arising from the use of such products. no license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of nec or others. descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. the incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. nec assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. while nec endeavours to enhance the quality, reliability and safety of nec semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. to minimize risks of damage to property or injury (including death) to persons arising from defects in nec semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. nec semiconductor products are classified into the following three quality grades: "standard", "special" and "specific". the "specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. the recommended applications of a semiconductor product depend on its quality grade, as indicated below. customers must check the quality grade of each semiconductor product before using it in a particular application. "standard": computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "special": transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "specific": aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. the quality grade of nec semiconductor products is "standard" unless otherwise expressly specified in nec's data sheets or data books, etc. if customers wish to use nec semiconductor products in applications not intended by nec, they must contact an nec sales representative in advance to determine nec's willingness to support a given application. (note) (1) "nec" as used in this statement means nec corporation, nec compound semiconductor devices, ltd. and also includes its majority-owned subsidiaries. (2) "nec semiconductor products" means any semiconductor product developed or manufactured by or for nec (as defined above).
nec compound semiconductor devices hong kong limited hong kong head office taipei branch office korea branch office tel: +852-3107-7303 tel: +886-2-8712-0478 tel: +82-2-528-0301 fax: +852-3107-7309 fax: +886-2-2545-3859 fax: +82-2-528-0302 nec electron devices european operations http://www.nec.de/ tel: +49-211-6503-101 fax: +49-211-6503-487 california eastern laboratories, inc. http://www.cel.com/ tel: +1-408-988-3500 fax: +1-408-988-0279 0110 nec compound semiconductor devices, ltd. 5th sales group, sales division tel: +81-3-3798-6372 fax: +81-3-3798-6783 e-mail: salesinfo@csd-nec.com business issue nec compound semiconductor devices, ltd. http://www.csd-nec.com/ sales engineering group, sales division e-mail: techinfo@csd-nec.com fax: +81-44-435-1918 technical issue m m m m pg2128tb safety information on this product caution gaas products the product contains gallium arsenide, gaas. gaas vapor and powder are hazardous to human health if inhaled or ingested. ? do not destroy or burn the product. ? do not cut or cleave off any part of the product. ? do not crush or chemically dissolve the product. ? do not put the product in the mouth. follow related laws and ordinances for disposal. the product should be excluded from general industrial waste or household garbage.
|
